Align RC Parts

Byron Fuel

Payment Method


  • Model: REV0010
  • Shipping Weight: 1 Kgs
  • Our Stock stock level
  • Manufactured by: REVOLECTRIX


Sold Out


Major Features
  • Charges Lithium Polymer, Lithium Ion, A123, NiCd, NiMH, and Pb packs. Charges any brand of pack.
  • Supports high-power balance charging of Li or A123 battery packs. Balance charges one 1s to 10s pack, or two 1s to 5s LiPo packs simultaneously. When two packs are connected, the balance connections and pack main discharge wires are wired in series by the charger.
  • Equipped with Cellpro brand (JST PA series times two, 6 position) balance connectors which enable the charger to monitor and independently charge each cell to its optimum level (balance charge operation).
  • Accepts Cellpro 10s Adapters for plug-and-play compatibility. Cellpro 10s Adapters support from 2s to 6s battery packs (all brands).
  • Backward-compatibility with older Cellpro 4s adapters is assured using the available 6-pin to 5-pin adapter(s) (REVO PN: CP10S-5S/4S-ADP-US) for charging 2s to 4s Cellpro packs having 5-pin balance connectors.
  • Also supports customer-selectable, XH MODE. JST XH/EH balance connectors and wiring are growing to be the dominant scheme in the industry. Switching to XH mode, the CP10XP can support existing XH/EH style adapters you may already own. Splice in REVO PN: CPBP6P-10-US battery pigtails to the balance wires on existing adapters and you are good to go!
  • Supports non-balanced charge of Li (up to 2s), Ni (up to 28 cells), Pb (up to 24V), A123 (up to 12s).
  • Accepts 10-32 VDC input.
  • Up to 15A max charge current.
  • Maximum 25A input current
  • 720W max continuous input and 605W max continuous output at 30V DC input. Charger will achieve rated output to a 10s LiPo using 30V DC input. Increasing input voltage beyond 30V does increase power output, but only if the charger's output voltage exceeds 42V; e.g., when charging 12s non-balanced A123 packs. However, 32V DC input is a maximum rating. It is recommended to utilize input voltage slightly below the absolute maximum.
  • Supports AUTO rate charging (1.0C, 2.0C, and 3.0C charge rate) using Advanced Fuel Gauging technology, or manual set currents of 0.10A - 15A in 0.10A increments.
  • Industry's largest 1A proportional integrated balancers
  • Power-balance-charge packs through balance connectors in tandem with the main discharge wires of the battery pack(s). Unit does not support balance-connector only charging.
  • Compensates for balance wire lengths up to six feet with 1mV accuracy.
  • Displays individual cell internal resistance to 0.1milliohm, for estimating pack quality, health, and performance.
  • Storage Preset available to charge or discharge Li batteries to appropriate per-cell storage levels; 3.8v (LiPo), 3.0v (A123).
  • During discharge to storage, the CP10XP incorporates 1A-per-cell (nominal) discharge rate using the charger's integrated balancing circuitry to provide up to 42W(at 10s)discharge power.
  • Supports Bi-directional, optional PC interface (REVO PN: FUIM2-US or FUIM3-US) which enables extensive charger setup using the CCS. Configure up to 10 custom presets, adjust speaker volume, set LCD contrast and control many other settings.
  • CCS automatically checks for software and charger firmware updates in the background. Update charger firmware reliably with the click of your mouse button, and without sending the charger back to the factory. Keep up-to-date with the latest enhancements and bug fixes.
  • 6 different, available Fuel Gauge lookup tables (fuel tables) may be assigned to independent presets to match the characteristics of different Li battery chemistries. This feature only available using the CCS.
  • Works with a wide range of power supplies, even those not rated for high power. Easily changes from moderate current bench supply at home to car battery at the field using the Power Management feature. Set Input supply amps limit and supply low voltage settings using the CCS or at the charger interface, to prevent damage to your input source.

Other Features

In addition to the unique features listed above, the Cellpro 10XP charger also has these features:
  • Light-grey, 2 line, 16 character backlit LCD display provides easy readability.
  • One button, Charge Optimization can be set for an Accurate 1mV cell balance and (C/20 termination) or for Faster Charging (less balancing accuracy and C/10 termination) using the Charge Control Software or at the CP10XP interface.
  • Protects your Pb input source from over-discharge by providing an audible warning when input voltage of your Pb battery approaches 50% state of charge.
  • Intelligent controller performs extensive checks to prevent damage to packs and power supply. This makes it virtually impossible to damage the charger or the batteries from incorrect connections or wiring; including, but not limited to reverse polarity.
  • Input reverse-polarity protection.
  • Simple, effective, 2-button interface allows instant access to presets, preset parameters, and starting and stopping charger operations.
  • Access pre-defined, named presets by clicking the MODE button.
  • Hold the MODE button to access the Main Menu operations: Choose Chg. Amps, Choose Chemistry, Show Help Screen, Exit. Use the charger's Main Menu to alter basic settings of presets on-the-fly, or make the adjustments using the free PC Charge Control Software (CCS).
  • Press and hold the START/STOP button to start charger operation or cancel/end a charging session.
  • Press and hold MODE button during power up to access Options Menu; choose input amps limit and supply low voltage setting (Power Management feature), alternate between FMA or XH balance wiring schemes, and set quiet charging (no speaker beeps during charging).

For Battery types: Lithium Polymer, Lithium Ion, Lithium Manganese, A123 (LiFEPO4), NiCd, NiMH, Pb packs

Supported Cell Counts:
LiPo, LiIon, LiMg - 1s-10s balanced, 1s, 2s unbalanced
A123 (LiFEPO4) - 1s-10s balanced, up to 12s unbalanced
NiCd - up to 28 cells (non-balanced)
NiMH - up to 28 cells (non-balanced)
Pb (Lead) - up to 24V

Pack capacity: 100mAh to 65Ah (charge time limited to maximum of 12 hours)

Input voltage: 10 to 32VDC; low voltage limit selectable from 10V - 28V in 0.5V increments (Power Management feature)

Input current: Up to 25A; can be limited to 1A to 25A in 0.5A increments (Power Management feature)

Power conversion: 62.5kHz switcher operating at 80% - 95% efficiency

Per-Cell output voltage:
LiPo, LiIon, LiMg - 4.10V, 4.20, or 4.22V
A123 (LiFEPO4) - 3.65V
NiCd - 1.20V
NiMH - 1.20V
Pb (Lead) - 2V

Output current: 100mA - 15A*, reverse polarity protected

Discharge current: 1A per cell nominal (42W max) for storage discharging Li

Cont. output current: 234W @ +12V DC input; 645W @ +32V DC input

Cell balancing Resolution: 78uV (16 bit) for 1s-10s Li or A123 LiFEPO4) balanced charging

Voltage calibration: Cell voltage measurements are factory calibrated to a standard traceable to NIST; calibration is to +/- 6 mV

Current calibration:Charge current is factory calibrated on a 4A standard; calibration is to +/- 1mA

Measurement accuracy:
Voltage resolution: 78uV (16 bit)
Voltage tolerance: +/- 6mV
Charge current: +/- 1%
Capacity added to pack: +/- 1%
Percent capacity (“Fuel”): +/- 10% (with accurate fuel table defined in preset)

Internal resistance: 0.1mohm voltage resolution allows accurate four point internal resistance measurement of each cell

Serial data output: 19.2kbps, 8 bits, 1 start bit, 1 stop bit, no parity

Data integrity: Checksum, CRC checking

Cooling fans: Single, 8 CFM, 40mm diameter

Heat sink: Aluminum case, finned

Output battery connector: “Cellpro” compatible, 2 x JST PA series, 6 position

LCD: 2 line, 16 character, light grey/blue backlit

Size: 6.83" x 3.67" x 1.70"

Firmware updates: Customer upgradeable using Charge Control Software (CCS)


Current Reviews: 0